Top 9 Maker Select V2 Heating Element

After-sales guarantee: each defective item can be replacement for free or refund. If any question, please feel free to contact or QA us, we will try our best to service you

Specification
Voltage: 12V
Power: 50W
Heating head size: 6 x 20mm
Heating head material: 304 stainless steel
Line length: 39inch /1M
Line thick: 0.5 mm?2; (The cross section of the copper wire inside the heater is 0.5mm?2;)
Color: as shown in the picture
Working Temperature: < 350="">

Single-end heating tube use instructions:
1.The effective heating part of the single-end heating tube must be kept dry.
2.The electrical joint of the single-ended heating pipe should be placed outside the insulation layer and the heating chamber. The working voltage should not exceed 10% of its rated value, and the casing should be effectively grounded.
3.The working environment of the electric heating element, the temperature is not more than 95 degrees, no explosive, corrosive gas.
4.The electric heating element should be stored in a dry place and should not be damp.

Package listing:
3 x 12V 50W Ceramic Cartridge Heater

After-sales guarantee: each defective item can be replacement for free or refund. If any question, please feel free to contact or QA us, we will try our best to service you

Specification
Voltage: 24V
Power: 50W
Heating head size: 6 x 20mm
Heating head material: 304 stainless steel
Line length: 39inch /1M
Line thick: 0.5 mm?2; (The cross section of the copper wire inside the heater is 0.5mm?2;)
Color: as shown in the picture
Working Temperature: < 350="">

Single-end heating tube use instructions:
1.The effective heating part of the single-end heating tube must be kept dry.
2.The electrical joint of the single-ended heating pipe should be placed outside the insulation layer and the heating chamber. The working voltage should not exceed 10% of its rated value, and the casing should be effectively grounded.
3.The working environment of the electric heating element, the temperature is not more than 95 degrees, no explosive, corrosive gas.
4.The electric heating element should be stored in a dry place and should not be damp.

Package listing:
3 x 24V 50W Ceramic Cartridge Heater

6x20mm 100CM Cable length 12V 40W Ceramic Cartridge Heater for 3D Printer.

Notes: The heating wire should not be bent. The product will be damaged after bending. If the product you received is not available, please contact us and we will provide satisfactory after-sales service for customers.

★The cartridge heater consists of a cylindrical stainless steel tube and thus provide high corrosion resistance.
★The inner heating wire is wound around the ceramic core.
★The number of coils varies according to power and provides a large uniform distribution of heat, which significantly increases the long life of the heater and prevents oxidation of the heater wire even at high temperatures.

Safety Guide:
★Recommend Safe Working Temperature: ＜300°C
★Must pay attention to the Safe working temperature of the 3D printer’s consumable and accessories, May cause high-temperature hazards!!
PLA (190°C-210°C)
ABS (230°C-250°C)

Warning!!
*This product is designed for 3D printers, always shut off the power of the circuit before starting installation work.
*3D printer accessories temperature can be very high, pay attention to safety!
*Due to the variety of possible uses, it is ultimately the responsibility of the customer to determine a product’s suitability for a particular application.

12V 40W 1/4-in (6.35mm) Ceramic Cartridge Heater
Fits Many MonoPrice/Flashforge/Wanahoo MK10 3D Printers with a 1/4in 6.35mm Bore Heater Hole

Please NOTE: This is a variation listing – You must select your voltage (12v or 24v) from the drop down menu at the top of the page

Specifications:
Product: Single-head heating tube
Diameter: 1/4 inch / 6.35mm
Length: 20mm
Wire Length: 3ft 3in / 1m
Voltage: 12 Volt
Power: 40 Watt

Package Contents:
1pc – 40W 12V Ceramic Heater Cartridge with a 1/4-in (6.35mm) Diameter

Product 1: Cartridge Heater
Material: stainless steel
Core: Nickel-chromium alloy
Resistance: 2080 high temperature resistant high-quality oxide powder
Voltage: 12V
Power: 40W
Diameter: 6mm
Length: 20mm
Wire Length: 1m
Product Usage: mold heating, hot core box, core shooting machine, and other media equipment heating

Product 2: Thermistor
High sensitivity, rapid response, compact structure, easy installation, wide temperature range, good stability, high reliability, Can provide different R, B value products, strong interchangeability, and high precision.

The main technical parameters of the product:
Nominal resistance: R25 (25 ° C): (commonly used) 1.5K, 2K, 5K, 10K, 20K, 30K, 47K, 50K, 100K, 200K, 500K, etc.
Resistance accuracy: ±1%, ±2%, ±3%
B value R25/50: (common) 3435K, 3600K, 3950K, 3990K, 4100K, 4200K, etc.
B value accuracy: ±1%
Operating temperature range: -40 ° C ~ +300 ° C
Dissipated power factor: ≥5 mW/°C (in static air)
Maximum rated power: 45mW
Thermal time constant: ≤ 7S (in static air)
Temperature coefficient of resistance: -2~ -5% / °C
Recommended parameters: R25°C=100K B25/50=3950K±1%

Package Included:
12V 40W Cartridge Heater X 6
3950 Thermistor X 6

3d printer heater block:
Inner hole for set screw: M6 and M3 (heat pipe and thermocouple)
Heater Mounting Hole: 6mm diameter
Thermocouple Mounting Holes: 3mm diameter
Suitable for Makerbot printer

12V 40W 620 Ceramic Cartridge Heater:
Material: 304 stainless steel
Lead wire: 0.3 square
Resistance: 2080 high temperature resistant high quality oxide powder

Application:
1 Semiconductor chamber heating
2 Semiconductor wafer lead connection
3 Semiconductor wire and die bonding
4 Freeze protection and deicing of equipment in cold climates or applications
5 Humidity Control
6 Patient Comfort heating used in medical devices
7 Mold die and platen heating
8 Seal bars used in packaging equipment
9 Test sample heating in gas chromatography

NTC 3950 100K Thermistor:
For 3D printers: use TEMP_SENSOR 11 in Marlin firmware
Small Size: 1.25mmx2.0mm glass bead
High accuracy: 1%
Resistance value at 25°C=100K
Wiring insulation: high temperature teflon / PTFE

Package Including
5 * 3d printer heater block
5 * 12V 40W 620 Ceramic Cartridge Heater
5 * NTC 3950 100K Thermistor

Specification:
Heater Cartridge:
Material: stainless steel
Core: Nickel-chromium alloy
Voltage: 24V
Power: 40W
Diameter: 6mm / 0.24″
Length: 20mm / 0.79″
Wire Length: 1m / 39.3″

Thermistor Cartridge:
Size: 1.25mmx2.0mm glass bead
High accuracy: 1%
Resistance value at 25°C=100K
Wiring length: 1m / 39.3″
Operating temperature range: -40 ° C + 300 ° C
Rated power: 45MW

Temperature Heat Resistant Tape:
Substrate material: Polyimide polymers film
Glue Type: Silicone
Substrate material thickness: 0.025mm
Thickness with adhesive: 0.05mm
Adhesive strength: 4.5N/25MM
Tensile Strength: 115N/25mm
Elongation: 50 %
Temperature Range:-73°C – 260°C

Package Included:
5 x Heater Cartridge
5 x Thermistor Cartridge
1 x Temperature Heat Resistant Tape
10 x Heating block cotton

Feature:
This great replacement for when the old ceramic tape wears out. It is used for 3D printer nozzle keeping warm.
The heating insulation cotton is made from heat-resistant ceramic fiber.
the product sizes can be customized according to customer needs.
the benefit for keeping the key parts of the 3D printer – heating aluminum block warm, is making the internal temperature flat, saving power,and energy.

Size: 75mm*21*2mm +/-0.2mm;

What You Get:10 x 3d printer heating block cottons;

Safety Guide:
Keep away from small children.
This products are only suitable for 3D printer use indoors.
Please read your use guideline of the 3D printer manual carefully before installing and using it.
<3d printer="" consumable:="" pla="" (190°c-230°c)="" or="" abs="" (230°c-250°c)="">

WARNING!!
3D printer replacement parts, Always shut off power to the circuit before starting installation work.
The surface temperature of the 3D printer might be high, and be careful not to touch the heating element to prevent injury.
3D printer initial operation, Do not run the equipment Unattended state.
When printing with a PLA(190°C-230°C) or ABS(230°C-250°C)consumable, if the temperature sensor and other accessories fail, it may cause high temperature hazards. Do not run the equipment Unattended state.
To ensure the users will use the product safely and properly, Please read your 3D printer manual first and follow the instructions step by step before using the product.
Due to the variety of possible end-uses, it is ultimately the responsibility of the customer to determine a product’s suitability for a particular application.