513 reviews analysed
1. 12V 60W Vacuum Transfer Pump Extractor Oil Fluid Diesel Electric Siphon with Hose for Car Boat Motorbike
Feature
- 5L oil liquid suction pump extractor,Small size, easy to carry and storage
- Maximum Pressure: Max. 0.8MPA,Maximum Flow: 5L/min, Rated Power: 60W, Rated Voltage: DC 12V
- Pump Diameter: Approx. 4.8cm, Cable Length: Approx. 30cm, Clips Length: Approx. 8cm
- Application: Widely used in general industrial equipment, medical equipment, chemical equipment, shipbuilding, drinks, carpet and floor cleaning, water purification and water treatment equipment, vehicle cleaning, agricultural spraying, zo pipeline pressure, air cleaning cooling, coal and metallurgical industries
- Pls use when the engine is warm,the engine oil is warm and viscosity is lower,this will be easier and faster to pump
Description
Specification:
Rated Voltage: DC 12V
Rated Power: 60W
Maximum Flow: 5L/min
Maximum Pressure: 0.8MPA
Pump Diameter: Approx. 4.8cm / 1.89inch
Length: Approx. 14.5cm / 5.7inch
Cable Length: Approx. 30cm / 11.8inch
Clips Length: Approx. 8cm / 3.15inch
Outlet PVC pipe Length:150cm
Nylon pipe Length:100cm
Brass pipe Length:70cm
Package include:
1x Oil Pump
1x 11mm Outlet PVC pipe
1x 6mm Nylon pipe
1x 5mm Brass pipe
How to use:
1.Start to run the car engine for a while, when oil temperature turns to be about 50 degrees, start pumping oil
2.Then connect the pump to the power, run it for a while, and observe whether the inlet and outlet is normal
3.Next,open the filler cap,get dipstick out, force the tube into the bottom of the joint, until the tube does not move; then put the inlet pipe from the oil dipstick into in end (the tube into the bottom of the tank, the bottom concave place, in order to pump the oil completely); as no oil or pumping up very slowly or intermittently, it is generally caused by loose pipes and fittings. You have to install the pipes and fittings again
4.After oil pumping, remove the tube, and then run the pump for a while, pump the remaining oil inside the pumping clean, or pump water for a while until the pump head gets clean
If you have not used it for a long time, it may have no suction, then just pour the water in the pump, and run the pump for a few minutes until the air is all out
Note: If you want to connect this pump to AC power, you will need a power converter.
2. DasMarine 12V 60W Oil Change Pump Extractor, Oil/Diesel Fluid Pump Extractor Scavenge Oil Change Pump Transfer Suction Transfer Pump + Tubes Truck Rv Boat ATV
Feature
- 【Specificaiton】: Input Voltage: DC 12V
- Wattage: 60W
- Current: 5A
- Motor Oil (40-60 degrees) Flow Rate: approx. 1L / min
- 【Easy Installation】: you just need to place the inlet and outlet hoses at the appropriate positions, connect the power clamps to the car battery and press the button. This process is very simple and you can often do it by yourself to ensure your engine runs smoothly.
- 【 Ideal Equipment For 】: Extracting Motor Oil From Your Vehicle Without Mess & Specialised Tools Extract The Oil From Your Car, Motorcyle, Scooter, Quad Bike, Truck, Boat, Forklift, Generator, Tractor, Ride On Mower Etc Siphon & Transfer Diesel To Cars, Trucks, Ships, Boats, Tractors, Farm Machinery, Plant Equipment Etc.
- 【WARNING】: This product is NOT suitable for gasoline/petrol. Do not use this pump to extract water, gearbox oil or easy flammable liquids (fuel, petrol etc)
- 【Package Included】: 1 x Pump
- 1 x Outlet Hose
- 1 x Inlet Hose
- 2 x Hose Clamps
- 2 x Battery Clamps
Description
Specifications:
Material: Plastic & Aluminium
Color: Black, Yellow
Input Voltage: DC 12V
Wattage: 60W
Current: 5A
Motor Oil (40-60 degrees) Flow Rate: approx. 1L / min
Diesel Flow Rate: approx. 250L / Hour
Inlet Hose Length: approx. 155cm/61”
Inlet Hose Outer Diameter: 6mm/0.236”
Inlet Hose Inner Diameter: 4mm/0.157”
Outlet Hose Length: approx. 124.5cm/49”
Outlet Hose Outer diameter: 12mm/0.472”
Outlet Hose Inner Diameter: 10mm/0.39”
Line Length: approx. 71cm/28”
Package Weight: approx. 1070g
Package Included:
1 x Pump
1 x Outlet Hose
1 x Inlet Hose
2 x Hose Clamps
2 x Battery Clamps
3. Briggs & Stratton 5431K Oil Extractor Pump, 4-Liter
4. OEMTOOLS 24389 Manual Fluid Extractor 179.2 Ounces
Feature
- MULTIPURPOSE EXTRACTOR: Designed to extract engine, transmission and lubricating oils from cars, motorcycles, marine engines and industrial machinery.
- VERSATILE APPLICATIONS: Extracts oil, power steering fluid and low-viscosity fluids, such as water and coolant.
- EASY-TO-USE: Includes 5 feet of flex hose and (2) specialized dipstick adapters to extract fluids directly from the dipstick tube.
- MINIMIZE CLEAN-UP TIME: 1.4 Gallon fluid reservoir features a dependable single-piece construction to drastically reduce oil and fluid spills during fluid maintenance jobs.
- OVERFLOW PROTECTION: Shut-off valve prevents fluids from overflowing.
Description
The OEMTOOLS fluid Evacuator has a 1.4 gallon (5.6 Quarts) reservoir with hand operated pump to tackle Big jobs and can be used to extract most fluid types: engine oil, transmission fluid, gear oil, coolant, power steering fluid.
5. Koehler Enterprises RA990 Multi-Use Siphon Fuel Transfer Pump Kit (for Gas Oil and Liquids)
Description
The Koehler Transfer Pump Kit allows for the safe and easy transfer of liquids between containers or vehicles, eliminating the risky practice of siphoning dangerous liquids by mouth. Transfer gasoline, oil, antifreeze and other liquids simply and quickly with no mess. The pump can also be adapted to an air pump function for inflating tires, air mattresses, sports equipment, water toys and other inflatables. Each kit includes a multi-use siphon pump, 1 each liquid intake and discharge hoses, two hose connectors, 1 each inlet and outlet nozzles, an air pressure hose and dipstick tube. Ideal for auto and equipment maintenance, RV and boat owners, farm, marine and industrial operations or any other application requiring easy and efficient fluid transfers.
6. Philips Norelco Multi Groomer MG7750/49-23 piece, beard, body, face, nose, and ear hair trimmer, shaver, and clipper
Feature
- 23 pieces for all your trimming needs: a metal trimmer, a foil shaver, a detail metal trimmer, a nose and ear trimmer, an extra-wide hair trimmer, 6 hair trimming guards, 3 beard trimming guards, 2 stubble trimming guards, 2 body trimming guards, an eyebrow trimming guard, a storage bag and a cleaning brush
- DualCut technology for maximum precision
- Powerful Lithium-ion battery delivers 5hrs of runtime
- Fully washable trimmer can be easily rinsed under the tap
- Reinforced guards won’t bend or buckle while trimming
7. Air Power America 2000LV Green Large Oil Extractor
Feature
- Easy to use
- 40 pump strokes creates a powerful vacuum – no electricity needed
- Fast – just a few seconds to drain oil from a small engine, takes a few minutes for large engines
- 8 quart capacity for big project large engine changes or multiple small engine changes
- Portable compact size, allows for easy oil changes in tight spaces
- No mess from spills or inconvenient drain plugs – used oil and other liquids are stored safely for proper disposal
Description
Product Description
Changing engine oil can be messy, time consuming and there is no good way to dispose of old oil. The LiquiVac is a new user friendly and environmentally safe oil changing system. It is fast, convenient and eliminates mess and clean-up. The LiquiVac works by creating a powerful vacuum that draws the used oil out of the engine and into a holding tank for easy disposal to a recycling center. Simply insert the extraction hose into the dipstick tube, pump the handle 40 times, release the hose clamp and LiquiVac extracts the oil directly into its plastic holding tank. Works great for boats, cars, trucks and more. USA dimensions: 16 inch length x 7 inch width x 11 inch height, tank size: 8 gallon, suction hose length 48 inches.
Amazon.com
Changing engine oil can be messy, time consuming and it is difficult to dispose of old oil. The LiquiVac is a user friendly and an environmentally safe oil changing system. It is fast, convenient and eliminates mess and clean-up. The LiquiVac works by creating a powerful vacuum that draws the used oil out of the engine and into a holding tank for easy disposal to a recycling center. Simply insert the extraction hose into the dipstick tube, pump the handle 40 times, open the cap’s valve and LiquiVac extracts the oil directly into its plastic holding tank. It works great for boats, cars, trucks–and small engines too.
Cars and Trucks Oil Change
The LiquiVac Oil Changing System for Large Projects and Engines makes car oil changes quick, clean, and easy. This is especially true with hard to access drain plugs found in large engines.
An average car or truck takes approximately 8-10 minutes to extract the oil, and without a mess. The Large Engine/Project Model comes with a special narrow suction hose to fit dipstick tubes of boats, cars, and light trucks. Plus, its tank has an 8 quart capacity allowing the user to make multiple oil changes of small engines too.
Boats
The LiquiVac innovative design makes it easier to change the oil in engines such as boats with inaccessible drain plugs. The Large Engine/Project Model comes with a special narrow suction hose to fit dipstick tubes to make your 4-cycle outboard oil change and inboard oil change easy. Also, don’t forget the LiquiVac makes boat transmission changes very easy.
Small Engines: Lawnmowers, Generators, Power Washers, Snow Throwers, and More
Small engines seem to be the most ignored engines that a consumer owns. This has occurred because there are consumers who have their car oil serviced at the quick lube places. And, have entirely forgotten that all the small engines in their garages need their oil changed too. Unfortunately this neglect can be very costly since these engines run very hard and in dusty conditions, which can lead to dirty, grimy oil and, eventually, engine breakdowns.
With the LiquiVac small engine oil changes are a snap. This vacuum is powerful enough to extract used oil out through the dipstick/fill tube in just 14 seconds. (Extraction time is based on the typical 4-cycle engine containing 1 quart of oil). With this kind of powerful performance and ease of use the LiquiVac Small Engine Model takes maintenance on 4-cycle engines super simple.
Which Model of LiquiVac Is Right for You?
LiquiVac Small Engine ModelSmall Engine Model
Small engines seem to be the most ignored engines that a consumer owns. This has occurred because there are consumers who have their car oil serviced at the quick lube places. And, have entirely forgotten that all the small engines in their garages need their oil changed too. Unfortunately this neglect can be very costly since these engines run very hard and in dusty conditions, which can lead to dirty, grimy oil; and, then engine breakdowns.
But, now there’s a simple, fast and clean way to change your lawn and garden equipment’s oil. It’s the LiquiVac Oil Changing System. With the LiquiVac oil changes are a snap. The LiquiVac Small Engine Model works by creating negative pressure, or vacuum power in the tank by pumping the tank handle. Each pump stroke takes air out of the tank creating a vacuum. Just 20 quick pump strokes creates vacuum power in the tank. This vacuum is powerful enough to extract used oil out through the dipstick/fill tube with the release of the suction hose clamp, in just 14 seconds. (Extraction time is based on the typical 4-cycle engine containing 1 quart of oil). With this kind of powerful performance and ease of use the LiquiVac Small Engine Model takes maintenance on 4-cycle engines very easy. Perfect for lawn mowers, lawn & garden tractors, tillers, generators, snow throwers, ATVs and outboard motors as well as.
LiquiVac Large Project/Engine ModelLarge Project/Engine Model
It is called the Large Project/Engine Model for a reason. Its 8 quarts capacity is large enough to handle several oil changes at one time, without recycling/emptying it. For example you can change your boat engine and several small engines in one session. Because of this, many do-it-yourself people love to knock out their oil change projects in one fell swoop. They can do it fast, without the mess. Plus, the Large Project and Large Engine Model works great for large engines such as hard to change boats (inboards and outboards), trucks, and cars too. It is also very handy for to change transmission oil and hydraulic fluids too.
8. Air Power America 5060TS Topsider Multi-Purpose Fluid Removing System
Feature
- Easy to use
- powered by vacuum pressure – no electricity needed
- Quickly extracts old oil through the dipstick tube into the 8 quart container
- Wide 12 inch diameter stance provides a stable base – eliminating any potential spills
- Portable – easy to operate in confined spaces
- No mess from spills or inconvenient drain plugs – used oil and other liquids are stored safely for proper disposal
Description
The Topsider’s reliability and convenience has long been trusted by boaters for easy, no mess oil changes, and other marine and automotive maintenance applications. No electricity required, the Topsider multi-purpose vacuum pump-out system uses a vacuum to pull oil out of your crankcase. A 12 inches diameter stance provides a stable base, eliminating potential tip-overs and spills, simply slide the withdrawal hose down your dipstick hole, open the valve and wait for 8 to 10 minutes. All of your old oil will be drawn into the Topsider’s 8 Quart container. Very easy to use, suction probe and instructions included.
9. Qiilu 12V 60W Oil/Diesel Fluid Pump Extractor Scavenge Oil Change Pump Transfer Suction Transfer Pump + Tubes for Auto Car Boat Motorbike Truck RV ATV Jet
Feature
- IDEAL TOOL-Ideal Equipment for quick and clean oil-changes. The oil will simply draw out the motor through the oil dipstick bore. Simple On/Off Power Switch, easy to use.
- HIGH EFFICIENT-This high efficient self-priming oil extractor pump is easy to pump various fluids and oils. You just need to place the inlet/outlet hoses at the appropriate positions, connect the power clamps to the car battery and press the button.
- PROFESSIONAL-Suitable for extracting oil, diesel etc from a vehicle, (never use for petrol).
- APPLICATION-Suitable for to pump engine, diesel and heating oil. Ideal for Motorcycles, Vans, Cars, Quads and Other 12v Vehicles.
- BEST CUSTOMER SERVICE-1Year Warranty.Within 24 Hours Online Service to answer any of your questions.We promise our kettle is same as our picture and description.
Description
Description:
This high efficient pump is an ideal equipment for quick and clean oil-changes. It works great for pumping engine oil, diesel and heating oil. About the installation, you just need to place the inlet and outlet hoses at the appropriate positions, connect the power clamps to the car battery and press the button. This process is very simple and you can often do it by yourself to ensure your engine runs smoothly.
Specifications:
Material: Plastic & Aluminium
Color: Black, Yellow
Input Voltage: DC 12V
Wattage: 60W
Current: 5A
Motor Oil (40-60 degrees) Flow Rate: approx. 1L / min
Diesel Flow Rate: approx. 250L / Hour
Inlet Hose Length: approx. 155cm/61”
Inlet Hose Outer Diameter: 6mm/0.236”
Inlet Hose Inner Diameter: 4mm/0.157”
Outlet Hose Length: approx. 124.5cm/49”
Outlet Hose Outer diameter: 12mm/0.472”
Outlet Hose Inner Diameter: 10mm/0.39”
Line Length: approx. 71cm/28”
Package Weight: approx. 1070g
Package Included:
1 x Pump
1 x Outlet Hose
1 x Inlet Hose
2 x Hose Clamps
2 x Battery Clamps
Note:
1. NOT suitable for extracting: water (no lubrication of the pump), gearbox-oil (too viscous) and easy inflammable liquids (petrol, gasoline, etc.)
2. The working-period for this oil-extractor should not exceed 30 minutes.
3. Please allow 0~1 inch error due to manual measurement. Thanks for your understanding.
10. Briggs & Stratton 5430K Oil Extractor Pump, 1.6-Liter
Description
Display pack of 1.6 liter oil extractor pump. Suitable for the extraction of oil fuel from outdoor power equipment, cars, motorcycles, commercial vehicles, marine engines, stationary engines and other machinery.
Conclusion
By our suggestions above, we hope that you can found Lawnmower Oil Vacuum for you.Please don’t forget to share your experience by comment in this post. Thank you!